Put Collabora Behind Nginx Without Breaking WebSockets
Configure Nginx TLS termination, Collabora routes, and WebSocket headers, then test the public endpoints before opening real documents.
Instructions on how to fix the darkest TV screen at home
Sure, every time you turn on the TV and the screen goes dark, try everything but the TV still doesn't turn on. You think the television is broken, and bring it to the store with the repair cost of up to several hundred million dong.
The tips that WebTech360 shares on how to best fix the dark TV screen at home will help you avoid unnecessary costs!
>> TV screen streaked: How to solve?
Case 1: TV has a light sensor feature
The light sensor feature on the TV will help the TV automatically adjust the screen light according to room lighting conditions. It may be in daylight conditions when you turn on the TV, and the TV will automatically dim the light.
So if you want the TV screen to have maximum or arbitrary brightness, you just need to go to: TV Settings> Power Saving> and here you find and turn off the light sensor (depending on each TV can be named sensor, light sensor, eco sensor ...).
Case 2: Due to the picture mode on TV
For each television, it will allow users to customize the picture modes to their liking. But this will affect the brightness of the screen.
- For example, on a Sony television, when you switch the picture in movie mode, the screen may go dark.
In that case, do the following:
- Go to Settings> select Picture (or screen, depending on TV model)> in the picture mode, you bring the TV to standard mode.
If you feel that the TV screen is still dark, you should overcome by increasing the brightness of the TV (Brightness) and the backlight (Blacklight). You should also only set the setting to about 40% to 60% when compared to the maximum, and should not set the TV screen too bright because it will cause eye pain and when viewing the image will be bad.
Case 3: Due to the power saving mode on TV
It may be due to the battery saver mode on the TV, at which time the screen will go dark to help save power on your TV.
If you find that the TV screen is too dark, check the power saving setting on the TV to see if you have this mode turned on. If so, please turn it off to make the TV screen brighter or you can adjust to the lowest level of savings.
Case 4: The video source is not bright
The screen brightness sometimes depends on the video quality, such as when you watch movies with USB on the TV, even though the screen brightness is very good, but the video you play is a bit dark when you watch on TV is still dark as usual.
To overcome this, now you need to watch content from multiple sources such as watching from USB, connecting a laptop, watching TV, or watching online movies from YouTube, FPT Play, ... If you see video in the morning and evening, you will be able to connect. Note that the dark TV is the source of your dark video input.
The above are the causes and solutions for a dark TV screen. If you have checked and applied the methods in this article, but the brightness of the TV is still unchanged, the TV screen is still dark then it is time to bring the TV to a genuine service center or You contact reputable television repair services.
See more:
>>> Instructions on how to factory reset Sharp Smart TV 2018
>>> Detailed instructions on how to factory reset TCL smart TV
Stop CODE Editing Sessions from Ending at 10 Minutes
Trace a 10-minute CODE disconnect to its proxy, load balancer, or WebSocket path, then correct the timeout and verify the session stays connected.
Deploy Collabora CODE on Kubernetes with Helm
Install the official Collabora Helm chart, configure WOPI access and ingress affinity, and verify the deployment without common setup mistakes.
Trace a Blank Collabora Document to the Failing Layer
Use browser requests, WOPI logs, and targeted proxy checks to find why Collabora opens a blank document—and choose a fix that fits the evidence.
Enable Multilingual Spell Check in Collabora Online CODE
Configure CODE Docker dictionaries and tag document passages correctly so English, French, and other supported languages receive the right spell-checking.
Set Collabora’s Idle Timer for Active Document Views
Adjust the per-view inactivity threshold in coolwsd and distinguish it from background-tab dimming, document unloading, autosave, and login expiration.
Disable Collabora CODE Update Checks and Unwanted Connections
Stop scheduled CODE update checks, review optional remote services, and use outbound network controls without breaking document editing.
Connect Seafile and Collabora with the Correct WOPI URL
Enable secure document editing in Seafile by configuring Collabora’s discovery URL, HTTPS, and WOPI access for your deployment.
Restore Copy and Paste Between Collabora and Desktop Apps
Test the system clipboard, adjust browser permissions, and identify when an embedded Collabora integration needs an iframe policy change.
Make Custom Fonts Available in Collabora CODE Docker
Mount font files into Docker and Collabora’s systemplate so custom typefaces appear in the editor and render correctly in documents.