Today's washing machines are gradually becoming an indispensable item in households. When using a washing machine for many years, having a washing machine not being washable is very difficult to avoid. Coming to this article, WebTech360 will help you find the causes and solutions for the washing machine not washing condition.
Causes of the washing machine not washing and how to fix it
Depending on the cause, we will have different ways of handling and solutions. Here are 6 causes of washing machine can not wash:
1. The washing machine does not start
First, check that the machine's power cord is firmly plugged into the power outlet or still loose, then check whether the cord is broken or open. Finally check the socket by using the electric tester, it is likely that the supply is not working and the socket is not receiving voltage.
After checking, start the washing machine with the Start / Pause button and run the washing cycle. If after the inspection is complete, but still cannot fix the error, call the warranty center or reputable washing machine repair units for assistance.
You need to check the power supply then start the machine
2. The detergent and fabric softener compartment is not closed
On front load washer products, the detergent and fabric softener compartment is usually outside the washing bucket. If the detergent drawer is not closed, the system will not allow the machine to operate. Make sure that the washing machine's detergent and fabric softener compartments are fully closed.
Close the detergent and softener drawer for machine to operate
3. The washing bucket contains too many clothes
This error stems from the habits of improper use of consumers. Users often tend to put many things into the machine to save time, electricity and water for one wash. However, this is not a good thing for the washing machine operation.
When the washing bucket contains too many clothes, the internal load sensor transmits a signal to the controller to prevent the washing machine from operating. In addition, storing too many items in one wash not only causes the washing machine to deteriorate quickly, but also makes clothes and blankets not washed clean.
When the washing machine cannot wash due to overload, take the initiative to remove the contents, divided into two washings to ensure long-term operation of the device.
Remove clothes when washing machine overloads
4. The washer door is not closed
Preventing the washing machine from working while the door is open is one of the mandatory safety systems on a washing machine. So make sure the door is closed before pressing the Start button to start the washing cycle.
Close the door and press “Start” to start washing
5. Belt, motor is broken
For washing machines that use belts in the transmission system, prolonged use will cause the belts to loosen, slip out of the engine or, most severely, break. To check the belt, remove the washer cover from the side or back of the washer to see. Particularly for top-loading washing machines, belts are located at the bottom, so need to turn the bottom of the washing machine up to check.
If the washing machine's belt is damaged or broken, check the serial number and type of the cord that the washing machine is using to find and buy and replace it or ask the repair service to help.
Direct drive washer products often have very durable engines and are less likely to fail. So when the engine has trouble, call the warranty center or repair unit for advice and support.
Check the belt and replace if necessary
6. Board fault, hardware related fault
The repair of hardware-related errors is very complicated, requires a lot of skill and expertise, so it is not possible to repair at home. If the washing machine cannot perform the washing due to a fault related to the motherboard, the only thing you should do is pick up the phone and call the distributor for warranty.
Hardware repair requires high skill
What to pay attention when the washing machine resolves the washing machine not washing condition?
When troubleshooting errors that prevent the washing machine from working, you need to disconnect the power supply for your own safety. Besides, when checking, if the fault is hardware or too difficult to fix, you need to call the repair staff or the place of purchase if it is still within the warranty period. If you still try to fix it, it could make the washing machine's condition worse.
>> See also: The washing machine does not drain fabric softener: What is the cause?
>> See also: What signs warn your washing machine is about to fail?
The above are the causes and solutions when the washing machine can not wash. If you have any questions, you can leave a message in the comments below. Wish you success.