During use, the loss of microwaves that prevent the microwave from heating food is one of the most common mistakes encountered during the use of equipment in many different brands, large and small.
There are many reasons from subjective to objective, and what causes the microwave oven to fail and how to fix it at home in the best way? Let's find out with WebTech360 in the article below!
The principle of microwaves to heat or cook food is that by means of a high-frequency bulb, it emits extremely short waves, or microwaves. When the oven light is on and the dish is still spinning but the food cannot be heated, the microwave is lost due to the transmitter failure.
Damaged transmitter loses microwave waves
Reason:
- Damaged high-frequency bulbs could be caused by leaving microwave ovens running at maximum 100% capacity for a long time, causing them to overheat and heat away in time.
- Then the fuse part of the microwave will break to protect the high frequency ball.
Microwave fuse
How to fix:
- Unplug the microwave power cord from the outlet, open the door and take out the food, remove the rear cover of the oven, find and take out the fuse box, pay attention to leave the wire part intact.
- Open the fuse box, then take the 2 ends of the wire attached to the fuse and use an electric tester to check whether the fuse is lit or not.
- If the fuse is broken, replace it with another fuse of the same type as offered by the manufacturer, then install it in the old position and close the oven cover.
- Then when you replace or reconnect the fuse, you plug in the power plug, put the food in the oven and set the capacity, modes, timers, wait time, you take the food out, finally Seeing that the dish was already hot, the fuse replacement was successful already.
Reconnect microwave fuse
Any household appliance will be dirty after using time. If you do not maintain or clean it, it will result in unintended damage that you did not anticipate. If the microwave oven you have been using for many months has not been cleaned, long-term cleaning substances from the food will accumulate and fill the bottom of the oven wall, preventing the waves from being emitted, preventing the oven from getting hot.
The wave blanket is so dirty that stains stick to the bottom of the oven wall
How to fix:
- After finishing the cooking process, use a soft cloth to soak it with warm water and then clean the oven compartment and cover. If the stains are stubborn, you can use mild detergents or natural detergents such as lemon, vinegar ... to clean.
- Deodorize the microwave: Put 1 cup of fresh lemon juice, microwave for about 3 minutes, then wait a few minutes for the boiler to cool down, take out the cup of water, then use a clean towel to quickly and more convenient.
Microwave cleaning
Many consumers do not know how to use and what items should be used in the oven, leading to the wrong use of containers and not fully functional microwave ovens.
Use food containers that cannot be used in the microwave
Food containers should not be used in the microwave such as: metal materials, containers with metal decorative patterns such as iron, stainless steel, aluminum ...
During the heating process, the sparks in the microwave will be emitted causing microwave reflections that prevent the oven from getting hot, making the food not hot and thawing it.
How to fix:
- Choose materials that can be used for microwave ovens such as porcelain, ceramic, hard plastic, ...
Above are the causes of microwave oven not hot and how to fix it at home. I wish you a successful remedy!
Connect ONLYOFFICE DocSpace to Active Directory or OpenLDAP, import users and groups safely, map account fields, and schedule reliable synchronization.
Move portal data from Disk Default to a supported cloud storage provider, or relocate Docker data safely by changing its host volume mapping.
Identify whether Document Server uses a Linux package or Docker, remove only its components, and check remaining data without deleting shared services by mistake.
Trace slow collaborative editing to Docker resource pressure, proxy connections, or document load, then choose the fix that matches your measurements.
Install custom fonts in ONLYOFFICE Document Server, compare persistent Docker mounts with direct copies, rebuild the font list, and verify the result.
Choose where TLS should terminate, mount a trusted certificate and private key safely, and verify HTTPS access to a Dockerized ONLYOFFICE Docs server.
Embed the ONLYOFFICE editor in your PHP app, sign its configuration with JWT, and save edited files through a secure callback.
Set the proofing language for the whole document or selected text, confirm spell checking is active, and identify when a server dictionary is missing.
Enable persistent Track Changes for everyone in one ONLYOFFICE document, verify edits are recorded, and understand the limits of this setting.
Find whether Nginx, Docker networking, or an internal ONLYOFFICE service is returning 502, then verify the corrected upstream and health check.
